Key Difference 1 FX & FORMA, Precise Energy Delivery Through Quantitative Treatment

InMode's FX (fat reduction) and FORMA (collagen lifting) have a set maximum output, so sufficient time and energy must be applied to achieve the desired results.

For FX treatments, we operate the device for more than 6 minutes, and for FORMA treatments, we maintain energy values above 10K, adhering to the standard.

We aim for precise treatment, delivering only the necessary energy without injecting anything superfluous.

Our medical professionals perform treatments directly, striving to contribute to treatment safety and improved results.

Key Difference 2 Delicate Approach for Efficient Temperature Rise and Maintenance During FX Treatment

For FX treatments, positive results can be expected only if the temperature reaches and is maintained above a certain level to break down fat cells.

We strive to raise and maintain the temperature quickly while minimizing discomfort by,

carefully adjusting the output, suction pressure, treatment speed, sequence, and skin reaction.

-We use energy at maximum output. This allows for a smoother temperature rise.

-We apply a longer pulse duration. By increasing the radiofrequency injection time per session, energy delivery through the tip is optimized, contributing to temperature elevation.

-We check the treatment area temperature with the back of our hand. In addition to InMode's real-time temperature monitoring, our medical staff delicately check the patient's treatment area temperature with the back of their hand during treatment to help alleviate discomfort.

-We adjust the speed of movement for each area. In the initial stage of treatment, heat is evenly distributed across the entire skin, and then the temperature is intensively raised in areas of concern or areas with a lot of fat, to reduce pain while enhancing the treatment effect.

Key Difference 3 Treatment Through Meticulous Design Process – A Delicate Approach to Minimize Cheek Hollowing

Since FX treatment aims for fat reduction, a careful design process before the procedure is crucial.

Inappropriate treatment can cause cheek hollowing, so we proceed with the procedure after carefully designing the areas for asymmetry improvement and focused treatment with our medical staff.

We meticulously analyze each individual's face shape and fat distribution to create a treatment plan that promises natural and harmonious improvements.

Key Difference 4 Post-Treatment Quantity Verification Process – Transparent and Reliable Treatment

After the treatment, we directly show patients the treatment duration and whether the quantitative energy was applied. This aims to build trust in the precise execution of the treatment.

Understanding InMode Treatment

*Radiofrequency (RF) lifting is mainly categorized into two methods.

1. Monopolar

This method involves energy emission from a single electrode and energy recovery through a pad attached to the body.

Energy is delivered deep into skin tissues, creating a strong deep-heat effect, but it can be accompanied by a relatively stimulating sensation.

2. Bipolar

Energy flows between two electrodes, primarily acting concentrated on the skin surface and dermis layer.

It has a lower pain burden and is relatively safe, but it is characterized by the difficulty of energy reaching relatively deep fat layers.

*What is the principle behind InMode FX acting on the fat layer despite being a bipolar method?

As explained earlier, bipolar methods generally have difficulty delivering energy to the fat layer.

However, InMode FX has a unique structure that allows it to effectively target the fat layer while utilizing a bipolar method.

The core of this lies in its vacuum suction function.

It gently suctions the skin and subcutaneous fat layer of the treatment area, positioning them stably between the two electrodes.

When radiofrequency energy is delivered in this state, heat can effectively penetrate even deep layers, despite it being a bipolar method.

Through this treatment method, fat cells undergo a process of damage at temperatures of around 42-45 degrees Celsius.

Damaged fat cells are naturally expelled through the lymphatic system, and simultaneously, collagen production can be stimulated in the dermis layer.

This allows for the simultaneous expectation of fat reduction and improved skin elasticity.

*Expected Effects of InMode FX Treatment

1. Fat Reduction Effect

When a constant heat of 42-45 degrees Celsius or higher is maintained for more than 6 minutes, the cell membranes of fat cells are damaged by the heat.

The contents of damaged cells are expelled from the body and can naturally exit through the lymphatic system.

This procedure is expected to help break down fat and is suitable for areas with relatively abundant subcutaneous fat, such as the cheeks or double chin.

2. Induces collagen production

In addition to the heat delivered to the fat layer during the procedure, the dermis layer also receives thermal stimulation, activating fibroblasts to create new collagen.

Simultaneously, existing collagen fibers show a contraction response, allowing for some degree of lifting effect immediately after the procedure.

*Features of InMode FORMA

The FORMA treatment specifically focuses on delivering high-frequency energy to the relatively shallower dermis layer, rather than the fat layer.

By gently moving the device over the skin surface, a stable temperature of approximately 42-43 degrees Celsius is delivered to the dermis layer.

This temperature activates fibroblasts, which can help improve various skin concerns such as fine lines, enlarged pores, and reduced skin elasticity.

FORMA is equipped with a system that measures and provides real-time temperature feedback, allowing for stable skin temperature maintenance throughout the entire procedure.

Thanks to this system, collagen production can be induced at a consistent temperature without subjecting the skin to excessive thermal stimulation.

Immediately after the procedure, you may experience a feeling of skin tightening, and the collagen regeneration process primarily occurs over 2 to 6 weeks.

*FX and FORMA: Appropriate Treatment Areas?

Facial sagging or fat accumulation can occur due to various reasons.

- Double Chin

A double chin generally appears due to an excessive accumulation of subcutaneous fat under the chin or a decrease in the elasticity of the muscles around the jaw.

The FX procedure helps break down fat cells by delivering concentrated high-frequency heat to the fat layer of the double chin area. It also induces collagen regeneration, which can improve the skin under the chin.

If the double chin has thin skin or significantly reduced elasticity, combining FORMA as a complementary method can be considered.

- Cheeks Below the Cheekbones (Jowls)

The cheeks below the cheekbones, commonly referred to as 'jowls,' are a typical sign of mid-face aging, appearing as facial fat sags downwards with age. The FX procedure reduces excessive fat volume, and

reinforcing skin elasticity with FORMA is expected to have a positive impact on overall facial contour improvement.

- Cheeks / Side Cheeks

Enlarged pores, fine lines, and rough skin texture are typically skin changes that occur as collagen density in the dermis layer decreases.

FORMA stimulates fibroblasts through high-frequency thermal energy to promote collagen and elastin production. This can help improve skin surface density and smooth skin texture.

- Jawline

A blurred jawline is often caused by reduced skin elasticity rather than solely a fat issue. In such cases, using FORMA to deliver concentrated thermal energy to the dermis layer to induce collagen contraction and regeneration can be effective.

If FX treatment is combined as needed, it can help create a more defined facial contour.

- Eye Area, Forehead, Mouth Area

These areas have relatively thin and sensitive skin, making them prone to fine lines.

FORMA can deliver the necessary energy even with relatively low output, allowing for effective treatment in these sensitive areas with reduced burden.

*Important Points for InMode Treatments

Simply owning an InMode device does not automatically guarantee the outcome of the procedure.

The success of the treatment heavily relies on the combination of handpieces, depth of thermal energy penetration, total accumulated energy, and a customized approach considering each individual's skin condition.

For example, with FORMA treatment,

simply applying a warm sensation to the skin does not immediately generate collagen.

In reality, a temperature of 42-43 degrees Celsius must be continuously maintained deep within the dermis layer for at least 10 minutes,

and a sufficient accumulated energy of at least 8-12 kJ per area must be delivered for fibroblasts to be actively stimulated and produce collagen.

The FX treatment follows a similar principle. Simply applying radiofrequency (RF) energy is not enough; a combination of vacuum suction and high-frequency heat must be effectively used.

Through the synergy of these two technologies, when deep heat of over 42 degrees Celsius is delivered deep into the skin for more than 6 minutes, both fat breakdown and collagen contraction effects can be expected simultaneously.

It is necessary to deliver appropriate energy of at least 8-15 kJ per treatment area, and for areas with thin skin or prone to bruising, precise adjustment of vacuum pressure is crucial.

Therefore, performing the FX treatment first to focus on the fat layer, followed by FORMA to enhance skin elasticity, can help achieve a synergistic effect.

It helps control swelling and heat that may occur after the procedure, while simultaneously creating a smooth, lifted contour.

In summary,

When considering an InMode procedure, it's fair to say that the anatomical knowledge of the medical staff performing the procedure, their ability to adjust equipment settings, and their skill in creating personalized designs are more important than just the equipment itself.

Our medical staff adheres to the aforementioned standards, continuously researching and applying treatment methods for optimal lifting effects.

Even with the same InMode procedure, we strive to increase patient satisfaction with the treatment results through a more delicate approach that considers individual characteristics.

Procedure Steps

Step 1 FX: This step utilizes a combination of radiofrequency energy and IRE (electrical stimulation) technology. It affects from the epidermal layer to the SMAS layer, aiding in overall facial lifting. During this process, it can help reduce fat cells and induce collagen production to refine facial contours.

Step 2 FORMA: This step delivers appropriate thermal energy to the dermal layer, stimulating collagen production, which can lead to improved wrinkles and enhanced skin elasticity.

All procedure steps are personally performed by our medical staff.